SensorData = 0;
unsigned long previousMillisSerialPrint = 0;
unsigned long previousMillisDCFPulseLength =... en der Sensoren
const unsigned long intervalSerialPrint = 100; // konstanter Delay für serielle Ausgabe... _t x = tft.readcommand8(ILI9341_RDMODE);
Serial.print("Display Power Mode: 0x"); Serial.println(x, HEX)... x = tft.readcommand8(ILI9341_RDMADCTL);
Serial.print("MADCTL Mode: 0x"); Serial.println(x, HEX);
x =
as OLED-Display
unsigned long previousMillisSerialPrint = 0; // Ausgabe an die serielle Schnitt... as OLED-Display
const unsigned long intervalSerialPrint = 500; // Ausgabe an die serielle Schnitt... , OUTPUT);
digitalWrite(13, HIGH);
Serial.print("PWM frequency PIN D9 and D10 is set to: "); Seri... quencyFan);
}
if(successPeltier) {
Serial.print("PWM frequency PIN D3 and D11 is set to: "); Seri
as OLED-Display
unsigned long previousMillisSerialPrint = 0; // Ausgabe an die serielle Schnitt... as OLED-Display
const unsigned long intervalSerialPrint = 500; // Ausgabe an die serielle Schnitt... , OUTPUT);
digitalWrite(13, HIGH);
Serial.print("PWM frequency PIN D9 and D10 is set to: "); Seri... quencyFan);
}
if(successPeltier) {
Serial.print("PWM frequency PIN D3 and D11 is set to: "); Seri
as OLED-Display
unsigned long previousMillisSerialPrint = 0; // Ausgabe an die serielle Schnitt... as OLED-Display
const unsigned long intervalSerialPrint = 500; // Ausgabe an die serielle Schnitt... , OUTPUT);
digitalWrite(13, HIGH);
Serial.print("PWM frequency PIN D9 and D10 is set to: "); Seri... quencyFan);
}
if(successPeltier) {
Serial.print("PWM frequency PIN D3 and D11 is set to: "); Seri
as OLED-Display
unsigned long previousMillisSerialPrint = 0; // Ausgabe an die serielle Schnitts... as OLED-Display
const unsigned long intervalSerialPrint = 500; // Ausgabe an die serielle Schnitts... , OUTPUT);
digitalWrite(13, HIGH);
Serial.print("PWM frequency PIN D9 and D10 is set to: "); Seri... quencyFan);
}
if(successPeltier) {
Serial.print("PWM frequency PIN D3 and D11 is set to: "); Seri
----");
//Ausgabe des Zeitstempels
Serial.print("[ "); Serial.print(millis()); Serial.println(" ms ] ");
// Ausgabe der Eingangssignale an den digita... nde Blumenkastensensor angeschlossen ist
Serial.print("Sensor Kasten 1: "); Serial.print(masse1); Serial.print(" \t");
Serial.print("Sensor Kasten 2: "); Se
, der an den Webserver übertragen wird
void debugPrint(const String &message) {
#if defined DEBUG
Se... er_wakeup(TIME_TO_SLEEP * uS_TO_S_FACTOR);
debugPrint("Setup ESP32 to sleep for every " + String(TIME_T... ntlichen die MAC-Adresse (Länge: 6 Bytes).
debugPrint("ESP32 Chip ID = " + String((uint16_t)(chipid >> ... // SDA, SCL
// Verbindungsaufbau WLAN
debugPrint("Connecting to " + String(WIFI_SSID));
WiFi.beg
llisEffect = 0;
unsigned long previousMillisSerialPrint = 0;
// Definiert die Intervalle für die IF-Abfr... 5; // Delay für Effekte
int intervalSerialPrint = 1000; // Delay für serielle Ausgabe
void set... begin();
// locate devices on the bus
Serial.print("Locating devices...");
Serial.print("Found ");
Serial.print(sensors.getDeviceCount(), DEC);
Seria
